English
GLB318L
Asialeren
8517710000
100pc
Accepted
10000pc/day
| Quantity: | |
|---|---|
| PDF Export | |
Item | Specifications | ||
GNSS Antenna (2 pins) | Dielectric Antenna | Frequency Range-MHz | GPS:1561.098~ 1575.42(L1-Band) QZSS: 1563-1587(L1) Galileo: 1559-1591(E1) GLONASS: 1602.0-1614.94 |
Polarization | RHCP | ||
Gain | 5dBic（Zenith） | ||
V.S.W.R | ＜1.5 | ||
Impedance | 50Ω | ||
Dimension | 33.5*33.5*6mm | ||
Axial Ratio | 3dB | ||
LNA | Gain | 28±2dB | |
Noise Figure | ＜1.5dB | ||
V.S.W.R | ＜2.0 | ||
Supply Voltage | 3~5.5V DC | ||
Current Consumption | ＜25mA | ||
LTE Antenna | Frequency Range | 698~960MHz/1710~2690MHz | |
V.S.W.R | ≤3.0 | ||
Polarization | Linear | ||
Gain | 2dBi | ||
Impedance | 50Ω | ||
DC resistance | 10KΩ | ||
Mechanical | Cable | RG174 or others | |
Connector | SMA or others | ||
Radome Material | ABS | ||
Mounting Method | Magnet/Adhesive | ||
Environmental | Operating Temperature | -40℃~+85℃ | |
Relative Humidity | Up to 95% | ||
Ingress Protection | IP66 | ||
Vibration | 10 to 55Hz with 1.5mm amplitude 2hours | ||
Environmentally Friendly | ROHS Compliant | ||
Product Introduction
1. Dual-mode, full-band coverage
• GNSS: Supports GPS L1/L2, QZSS LL, Galileo E1, and GLONASS G3 (1602-1615MHz)
• LTE: 698-960MHz/1710-2690MHz (compatible with 4G full-band and 5G n1/n3/n7)
2. High gain, low noise
▸ GNSS antenna gain 5dBic (zenith direction)
▸ Built-in LNA gain 28±2dB, noise figure <1.5dB, 40% improvement in weak signal acquisition capability
3. Industrial-grade protection design
IP66 waterproof and dustproof (surpassing the previous generation's IP67 screw hole defect)
Passed 10-55Hz/1.5mm amplitude vibration test for 2 hours
ABS UV-resistant cover + 95% humidity resistance
4. Convenient deployment
• Dual magnetic and adhesive mounting options (load capacity not marked, requires actual measurement)
• Standard SMA connector (customizable), RG174 cable for interference prevention
• Cable identification system (heat shrink tubing printed with "LTE"/"GRSS" to prevent misconnection)
5. Wide-voltage, energy-saving design
3-5.5V wide input voltage, power consumption <25mA, compatible with vehicle battery/solar power systems
Application Scenarios
Fleet management system: Real-time positioning of freight vehicles + 4G data backhaul
Maritime navigation terminal: Vessel trajectory monitoring and offshore communications
Mobile emergency equipment: Rapid deployment of monitoring stations at disaster sites
Smart agricultural machinery: Autonomous agricultural machinery for coordinated operation
Industrial router: High-precision timing and networking for field base stations
FAQ
Q: Does it support North American Bands 12/17?
A: It covers 698-960MHz (including Bands 12/13/17). Please check the terminal certification for specific frequency bands.
Q: What is the holding force of the magnetic mount?
A: The manual doesn't specify this, but the measured vertical adhesion force at room temperature is ≥ 3 kgf (metal surface flatness < 0.5 mm recommended).
Q: What is the purpose of a 10 kΩ DC resistance?
A: The LTE antenna has a 10 kΩ DC resistance to prevent static electricity damage and improve lightning resistance.
Q: Can a GNSS receiver and LTE module be connected simultaneously?
A: Separate cables are required: the GNSS output is connected to the receiver, and the LTE is connected to the communication module (the cable heat shrink tubing is marked).
Q: What is the temperature range for adhesive mounting?
A: The adhesive operates at a temperature of -30°C to +80°C (lower than the antenna body's -40°C to 85°C). Magnetic mounting is recommended for high-temperature environments.
Q: Is a ground plane required for a 5 dBIC gain?
A: The integrated 33.5 × 33.5 × 6 mm dielectric antenna does not require an additional ground plane and can be mounted directly on a metal roof.
Item | Specifications | ||
GNSS Antenna (2 pins) | Dielectric Antenna | Frequency Range-MHz | GPS:1561.098~ 1575.42(L1-Band) QZSS: 1563-1587(L1) Galileo: 1559-1591(E1) GLONASS: 1602.0-1614.94 |
Polarization | RHCP | ||
Gain | 5dBic（Zenith） | ||
V.S.W.R | ＜1.5 | ||
Impedance | 50Ω | ||
Dimension | 33.5*33.5*6mm | ||
Axial Ratio | 3dB | ||
LNA | Gain | 28±2dB | |
Noise Figure | ＜1.5dB | ||
V.S.W.R | ＜2.0 | ||
Supply Voltage | 3~5.5V DC | ||
Current Consumption | ＜25mA | ||
LTE Antenna | Frequency Range | 698~960MHz/1710~2690MHz | |
V.S.W.R | ≤3.0 | ||
Polarization | Linear | ||
Gain | 2dBi | ||
Impedance | 50Ω | ||
DC resistance | 10KΩ | ||
Mechanical | Cable | RG174 or others | |
Connector | SMA or others | ||
Radome Material | ABS | ||
Mounting Method | Magnet/Adhesive | ||
Environmental | Operating Temperature | -40℃~+85℃ | |
Relative Humidity | Up to 95% | ||
Ingress Protection | IP66 | ||
Vibration | 10 to 55Hz with 1.5mm amplitude 2hours | ||
Environmentally Friendly | ROHS Compliant | ||
Product Introduction
1. Dual-mode, full-band coverage
• GNSS: Supports GPS L1/L2, QZSS LL, Galileo E1, and GLONASS G3 (1602-1615MHz)
• LTE: 698-960MHz/1710-2690MHz (compatible with 4G full-band and 5G n1/n3/n7)
2. High gain, low noise
▸ GNSS antenna gain 5dBic (zenith direction)
▸ Built-in LNA gain 28±2dB, noise figure <1.5dB, 40% improvement in weak signal acquisition capability
3. Industrial-grade protection design
IP66 waterproof and dustproof (surpassing the previous generation's IP67 screw hole defect)
Passed 10-55Hz/1.5mm amplitude vibration test for 2 hours
ABS UV-resistant cover + 95% humidity resistance
4. Convenient deployment
• Dual magnetic and adhesive mounting options (load capacity not marked, requires actual measurement)
• Standard SMA connector (customizable), RG174 cable for interference prevention
• Cable identification system (heat shrink tubing printed with "LTE"/"GRSS" to prevent misconnection)
5. Wide-voltage, energy-saving design
3-5.5V wide input voltage, power consumption <25mA, compatible with vehicle battery/solar power systems
Application Scenarios
Fleet management system: Real-time positioning of freight vehicles + 4G data backhaul
Maritime navigation terminal: Vessel trajectory monitoring and offshore communications
Mobile emergency equipment: Rapid deployment of monitoring stations at disaster sites
Smart agricultural machinery: Autonomous agricultural machinery for coordinated operation
Industrial router: High-precision timing and networking for field base stations
FAQ
Q: Does it support North American Bands 12/17?
A: It covers 698-960MHz (including Bands 12/13/17). Please check the terminal certification for specific frequency bands.
Q: What is the holding force of the magnetic mount?
A: The manual doesn't specify this, but the measured vertical adhesion force at room temperature is ≥ 3 kgf (metal surface flatness < 0.5 mm recommended).
Q: What is the purpose of a 10 kΩ DC resistance?
A: The LTE antenna has a 10 kΩ DC resistance to prevent static electricity damage and improve lightning resistance.
Q: Can a GNSS receiver and LTE module be connected simultaneously?
A: Separate cables are required: the GNSS output is connected to the receiver, and the LTE is connected to the communication module (the cable heat shrink tubing is marked).
Q: What is the temperature range for adhesive mounting?
A: The adhesive operates at a temperature of -30°C to +80°C (lower than the antenna body's -40°C to 85°C). Magnetic mounting is recommended for high-temperature environments.
Q: Is a ground plane required for a 5 dBIC gain?
A: The integrated 33.5 × 33.5 × 6 mm dielectric antenna does not require an additional ground plane and can be mounted directly on a metal roof.
